Samsung Washer SW80ASP User Guide

Owner’s Instructions  
SW80ASP/SW95ASP  
CONTENTS  
Page  
FEATURES ............................................................................................1  
DESCRIPTION OF PARTS....................................................................2  
SAFETY INSTRUCTIONS .....................................................................3  
INSTALLATION & MAINTENANCE......................................................4  
ENVIRONMENT................................................................................4  
IN CASE OF PUMP-DRAINED WASHER .......................................4  
HOW TO CONNECT WATER SUPPLY HOSE ................................4  
CLEANING THE FILTER NET..........................................................5  
HOW TO ADD THE DETERGENT ...................................................5  
HOW TO ADD THE FABRIC SOFTENER.......................................5  
CLEANING THE FILTER ..................................................................5  
LEVELLING.......................................................................................5  
PRECAUTIONS ................................................................................6  
WASHING INSTRUCTION.....................................................................6  
PROCEDURE ...................................................................................6  
WASH PROGRAM............................................................................7  
WASHING PROGRAM DETAILS..........................................................7  
OPTIONAL CYCLE................................................................................8  
TROUBLESHOOTING...........................................................................8  
SPECIFICATION  
 
DESCRIPTION OF PARTS  
WATER SUPPLY HOSE  
RED-HOT WATER  
LID  
WATER SUPPLY HOSE  
WHITE-COLD WATER  
DRAIN-HOSE  
DETERGENT BOX  
CONTROL PANEL  
POWER PLUG  
FABRIC SOFTENER  
DISPENSER  
BLEACH INLET  
MAGIC FILTER  
Lint will be collected in  
the filter during washing.  
HEIGHT ADJUSTING  
FEET  
CONTROL PANEL  
2
 
SAFETY INSTRUCTIONS  
WARNING!  
To reduce the risk of fire, electric shock, or injury to persons when using your appliance,  
take care to adhere to the following precautions.  
Maximum hot water supply temperature  
Where an unearthed power cord is not fitted,  
60 degrees.  
be sure that the washer is grounded.  
To avoid electrical shock use metal piping for the ground  
connection.  
●● Before washing, check all pockets.  
Take care not to ground the washer to  
If nails or pins remain in pockets, they may damage the  
gas pipes or telephone cables due to the  
washer or clothes.  
danger of explosion from lightning strikes.  
Don’t press the control panel with a sharp  
During spinning, don't put your  
hand in the spin basket.  
Because the spin basket is rotating at the  
object.  
Panel damaged or malfunction may occur.  
high speed, rotating parts may injure your  
hand.  
If the control panel for this washer is damaged,  
it must be replaced by a repair shop appointed by the  
manufacturer, as special purpose tools are required.  
●● Do not operate this appliance if it is damaged,  
malfunctioning, partially disassembled, or has  
missing or broken parts, including a damaged  
cord or plug.  
Openings must not be obstructed by carpeting  
when the washing machine is installed on a  
carpeted floor.  
Turn off water taps when the washer is not in  
use to avoid water pressure damage to the  
pump.  
Do not store or use gasoline or other flammable  
vapors and liquids in the vicinity of this or any  
other appliance.  
To minimize the possibility of electric shock,  
unplug this appliance from the power supply or  
disconnect the washer at the household  
distribution panel by removing the fuse or  
switching off the circuit breaker before  
The instructions for use shall specify the  
maximum mass or dry cloth in kg, for which the  
appliance is designed.  
attempting any maintenance or cleaning.  
If the appliance is supplied from a cord  
extension set or electrical portable outlet  
device the cord extension set or electrical  
portable outlet device should be positioned so  
it is not subject to splashing or ingress of  
moisture.  
The appliance is not intended for use by young  
children or infirm persons without supervision.  
Young children should be supervised to ensure  
that they do not play with the appliance.  
This appliance is not intended for use by young  
children or infirm persons unless they have  
been adequately supervised by a responsible  
person to ensure that they can use the  
appliance safely.  
Young children should be supervised to ensure  
that they do not play with the appliance.  
If the power supply cord is damaged, it must be  
replaced by the manufacturer or its service  
agent or a similarly qualified person in order to  
avoid a hazard.  
Place clothes evenly into the washer as  
unevenly distributed laundry may cause  
excessive out-of-balance noise and vibration.  
3
 
INSTALLATION & MAINTENANCE  
IN CASE OF PUMP-DRAINED WASHER  
ENVIRONMENT  
Be sure to join tightly the  
drain hose into the drain-  
outlet on the back of the  
machine.  
Install the drain hose in  
the position of about  
70~80 cm above the  
ground.  
Leave some space  
Maintain at least 10cm between the washer and  
the wall.  
Place the washer on a sturdy flat  
surface.  
If the washer is placed on an uneven or weak  
surface, noise or vibration occurs. (Allowable  
slope is 1 degree)  
Never install the washer in a very  
steamy environment or where it might  
be open to the rain.  
Excessive moisture may cause an electrical  
shock hazard.  
Avoid direct sunlight or heaters.  
As plastic and electrical components are affected  
by direct heat,never place the washer near  
furnaces, boilers,etc. Do not place under direct  
sunlight.  
HOW TO CONNECT WATER SUPPLY HOSE  
Check the type of tap fitting which is in your laundry and then see appropriate instruction below:  
A tap of ordinary type is desirable  
In case of square tap  
Take out the internal part of the connector  
and join it in the following way.  
Internal part  
ORDINARY TAP  
SQUARE TAP  
ROTATING TAP  
4. Connect the water supply hose  
1. Remove the adaptor from the  
water supply hose.  
to the adaptor. Pull down the  
part (c) of the water supply  
hose. When you release part (c)  
the hose is automatically  
connects to the adaptor making  
a 'click' sound.  
c
2. First,using a "+" type screw  
driver, loosen the four screws  
on the adaptor. Next,take the  
adaptor and turn part(b)  
following the arrow for gap  
about 5mm between them.  
5. Connect the other end of the  
water supply hose to the inlet  
water valve at the top of the  
washer.  
Screw the hose clockwise all  
the way in.  
a
b
6. If the water tap is a screw  
type,assemble a water supply  
hose that fits to the tap as  
shown.  
3. Connect adaptor to the water  
tap by tightening the screws  
firmly.  
Then,turn part (b) following the  
arrow and put (a) and (b)  
together.  
c
Note : The appliance is to be connected to the water mains using new hose-sets and that old hose-sets should not  
be used.  
4
 
CLEANING THE FILTER NET  
1.Push the upper part of  
the filter and pull in.  
2.Open the cover as  
shown in the figure.  
3.Clean the filter.  
4. Close the cover and insert the lower  
part of the filter in the basket first and  
then push the filter with "click" sound .  
HOW TO ADD THE DETERGENT  
LEVELLING  
Adjustment the heigt of the machine  
Adjust the legs to level the washer  
Be careful not to put in your hand under the legs.  
1. Open the detergent box by pulling in  
the direction of the arrow as shown in  
the figure.  
2. Add the amount of detergent for one  
washing evenly in the box so that the  
detergent does not overflow the box.  
Pull the handles located at the  
right and left of the front side and  
slide off.  
Adjust the height of the machine  
upward or downward.  
HOW TO ADD THE FABRIC SOFTENER  
When a proper amount of fabric softener is stored in the  
box, it is automatically added in at the final rinse cycle.  
In case the hot water only is connected, this function will  
not be operated.  
When the adjustment is finished,  
push the handles to fix the  
adjusting legs.  
SEE IF THE MACHINE IS PLACED LEVEL BY  
CHECKING THE POSITION OF THE WASHING TUB.  
When too much softener is stored above the base line, it  
may not be operated properly.  
Open the lid of the machine, pour water into the tub up to  
the level just below the pulsator, and adjust the legs so  
that the pulsator is positioned at the center of the water as  
shown in the figure.  
Place the machine more than 10cm away from the wall.  
Water  
CLEANING THE FILTER  
(pump drained washer)  
1. Place a rag under washer filter not to wet the floor.  
2. Turn the filter-cap to the left.  
3. Take out the filter and remove any sludge.  
4. Reassemble in reverse order.  
5
 
WARNING! NOTE THE FOLLOWING PRECAUTIONS TO PREVENT ELECTRICITY  
LEAKAGE AND THE POSSIBILITY OF ELECTRIC SHOCK.  
Earthing is necessary to prevent leakage or electric shocks caused by the electric currents leaked from the machine.  
How to earth an outlet with earthing terminals when  
an earthed power load is not fitted.  
Outlet with earthing terminals:  
Even when the internal wires of the earthing terminals are joined,  
connect the earthing conductor (green) of the machine to the tap.  
When using an extension cord and a boosting transformer:  
Make sure that the earthing conductor is connected.  
Never make an earthing to  
The telephone line, lightning rod, or gas pipe as it is  
extremely dangerous in case of lightning strikes.  
TO DO A CLEAN WASHING  
Press the POWER botton.  
Pour a little detergent into case-detergent.  
Turn on water supply to the wshing machine.  
Choose the SOAK in CYCLE button and the HIGH in WATER LEVEL button.  
Press the START/PAUSE button.  
WASHING INSTRUCTION  
PROCEDURE  
1
. Sort the laundry into separate wash loads.  
Each load of washing should contain clothing which needs the same washing conditions.  
For example, you should not wash delicate clothes with very dirty work clothes.  
2
. Load the laundry into washing.  
Before load, check all pockets, and close zippers, hooks and eyes.  
3. Add the detergent. (see page 5)  
4. Add the fabric softener. (see page 5)  
5. Close the lid.  
6. Press power button.  
7. Choose the wash program & optional cycle. (see page 7~8)  
If you choose SENSORprogram you dont need to select water level.  
Water level is set automatically at SENSORprogram.  
Press the START/PAUSE button.  
8. Select the water level.  
Before choosing the water level, remember following things.  
When you choose SENSOR, HEAVY-DUTY, ECONO-WASH, DELICATE program,  
water level is selected AUTOautomatically, but if you wat to choose water level manually  
you can select. HIGH, MEDIUM, LOW, EXTRA LOW  
6
 
9
. Select the water temperature.  
Before choosing the water temperature remember the following:  
1) You can choose HOT, WARM, COLD on all programs except for delicate program.  
HOT is hot wash and cold rinse.  
WARM is warm wash and cold rinse.  
COLD is cold wash and cold rinse.  
2) When you choose delicate program, water temperature is selected automatically for warm wash and warm rinse.  
10. Close the lid and press the START/PAUSE button.  
11. Do you wat extra rinse?  
For extra rinses press the cycle key 1 to 5 times (depending on the number of extra rinse required).  
You can select up to 5 extra rinses or return to a single rinse by pressing the cycle key.  
The time left display will show the number of rinses selected.  
Note tat the extra rinse program is not available when pause is selected or during the spin cycle.  
WASH PROGRAM  
WOOL  
6 min  
ECONO WASH  
5 min  
DELICATE  
6 min  
SENSOR  
18 min  
HEAVY DUTY  
20 min  
Wash Time (SW80ASP)  
Wash Time (SW95ASP)  
Wash Action  
6 min  
5 min  
6 min  
25 min  
26 min  
Gentle  
Normal  
Gentle  
Normal  
Normal  
HOT  
WARM  
COLD  
HOT  
WARM  
COLD  
HOT  
WARM  
COLD  
Wash Temp.  
WARM  
COLD  
WARM  
COLD  
WARM  
COLD  
WARM  
COLD  
COLD  
COLD  
COLD  
Deep Rinse  
Spin Time  
1 min  
3 min  
1 min  
6 min  
6 min  
36 min  
36 min  
40 min  
40 min  
37 min  
37 min  
Total Time  
SW80ASP  
(High Water level) SW95ASP  
56 min  
62 min  
59 min  
63 min  
WASHING PROGRAM  
SENSOR Program  
HEAVY DUTY Program  
The best washing program is chosen automatically  
Load size and water level is determined automatically  
This program is suitable for heavily soiled laundry  
Load size and water level is determined automatically  
or you can choose the water level you want  
Unplug the power cord after washing.  
Unplug the power cord after washing.  
ECONO WASH Program  
WOOL Program  
Saving your time and energy  
This program is suitable for woollen clothes  
This program is suitable for heavily soiled laundry  
Load size and water level is determined automatically  
or you can choose the water level you want  
Only high and medium water levels are available  
Unplug the power cord after washing.  
Unplug the power cord after washing.  
DELICATE Program  
Washing action is very gentle, so this program is  
suitable for delicate clothes like lingerie.  
Load size and water level is determined automatically  
or you can choose the water level you want  
Unplug the power cord after washing.  
7
 
OPTIONAL CYCLE  
WASH ONLY  
RINSE ONLY  
When you choose this cycle, wash cycle is operated.  
Pressing optional cycle key during washing changes  
the wash time in two minute intervals.  
The wash time can be changed to between 3 and 25  
minutes.  
When you choose this function, only rinse cycle is  
operated.  
Pressing function key during rinsing changes the  
number of rinse. Up to 5 rinses can be optionally  
selected.  
Load size and water level is determined automatically  
Unplug the power cord after washing.  
Unplug the power cord after washing.  
SOAK  
DRIP DRY  
The laundry is soaked in water so that heavy dirt can be  
The function allows you to take drip clothes out of the  
washing machine while they are still wet before the final  
spin.  
eliminated sufficiently.  
You can choose soak cycle after choosing wash  
program.  
When you select soak function, 5 minute cycle (1 min.  
washing then 4 min. pause) continue for 30 minutes  
before main wash program.  
You can choose drip dry cycle after choosing main  
wash program.  
When you select drip dry the cycle in finished before  
final spin.  
Load size and water level is determined automatically  
Unplug the power cord after washing.  
Unplug the power cord after washing.  
SPIN ONLY  
RINSE AND SPIN ONLY  
You can choose this cycle, only cycle is operated.  
Pressing cycle key during spinning only cycle changes  
the spin dry time.  
When you choose this cycle, only rinse & spin cycle are  
operated without wash cycle.  
Pressing cycle key during operation changes the  
number of rinse (see above).  
The spin dry time can be changed to between 1 and 7  
minutes.  
You cannot change the spin dry time using this function.  
Unplug the power cord after washing.  
Unplug the power cord after washing.  
DELAY START  
This function allows you to delay the start of your chosen wash program for 3, 4, ... 18 hours.  
By pressing the delay start key you can select delayed period for 3, 4, ... 17, 18 hours, and your washing machine will  
finish the selected wash program after the delayed period.  
TROUBLESHOOTING  
Washing machine won’t work  
Spinning does not work  
Is the water tap opened?  
Is the washer plugged in?  
Is the power cut off?  
Is the laundry spread out evenly  
in the washer?  
Is the washer set on a sturdy  
flat surface?  
Is the fuse all right?  
Is there enough water?  
Is the lid closed?  
Water does not drain  
Water is not supplied  
Is the drain hose down? (No pump)  
Is the drain hose frozen?  
Is the water tap opened?  
Is the water cut off?  
Is the drain hose clogged?  
Is the water supply hose or  
If the water does not drain in 15  
minutes, a buzzer will sound, and the  
remaining time indicator will show “E”  
hose connection clogged?  
Is the water tap frozen?  
If water is not supplied in 60 minutes,  
a buzzer will sound, and the remaining  
time indicator will shown “7E”.  
While lid is opening,  
Water supply does not stop  
the washing machine won’t work  
Make sure to close the lid while washing machine is  
operating.  
Close the water tap.  
Disconnect the power supply card.  
Call to service center or agency.  
8
 
IF YOU NEED HELP WITH YOUR NEW  
SAMSUNG WASHING MACHINE  
Contact your nearest Samsung office or Samsung authorized  
service center for technical assistance  
SPECIFICATION  
SW80ASP  
550  
SW95ASP  
Power input(Watts)  
Load capacity(kg)  
550  
8.0  
9.5  
Size(WxDxH)(mm)  
640 X 698 X 1050  
50  
640 X 698 X 1070  
50  
Net Weight(kg)  
Water Consumption(liters)  
Water Pressure(min-max)  
190(high)  
50~780KPa  
189(high)  
50~780KPa  
CODE NO. : DC68-01277A-01  
 

Rangemaster Oven R7247 User Guide
Rinnai Water Heater MSB C1 User Guide
Roberts Radio Portable Radio unologic User Guide
Ruckus Wireless Network Card MF2501 User Guide
Samsung Air Conditioner SH12UA1 User Guide
Samsung Blood Pressure Monitor BD 3000S User Guide
Samsung Flat Panel Television 400MP User Guide
Samsung Graphics Tablet GT P7500 User Guide
Samsung IP Phone SMT i5243 User Guide
Sears Saw 1132945 User Guide