TOA Electronics Portable Speaker F 2000B User Manual

OPERATING INSTRUCTIONS  
SPEAKER SYSTEMS  
F-2000B  
F-2000BT  
F-2000W  
F-2000WT  
F-2000BTWP F-2000WTWP  
Thank you for purchasing TOA's Speaker System.  
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.  
533-06-146-20  
 
1. SAFETY PRECAUTIONS  
• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe  
operation.  
• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or  
cautions regarding safety.  
• After reading, keep this manual handy for future reference.  
Safety Symbol and Message Conventions  
Safety symbols and messages described below are used in this manual to prevent bodily injury and property  
damage which could result from mishandling. Before operating your product, read this manual first and  
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.  
• Do not use anti-rust lubricant. If it contacts resin or  
rubber parts, they could deteriorate and cause the  
unit to fall, possibly resulting in personal injury.  
WARNING  
Indicates a potentially hazardous situation which,  
• Avoid installing the speaker in locations close to  
if mishandled, could result in death or serious  
the seashore or in indoor swimming facilities that  
personal injury.  
are not well ventilated. In such locations the  
bracket may be vulnerable to corrosion, eventually  
When Installing the Unit  
allowing the speaker to fall resulting in personal  
injury.  
• Install the unit only in a location that can  
structurally support the weight of the unit and the  
mounting bracket. Doing otherwise may result in  
the unit falling down and causing personal injury  
and/or property damage.  
CAUTION  
Indicates a potentially hazardous situation which,  
if mishandled, could result in moderate or minor  
personal injury, and/or property damage.  
• Do not use other methods than specified to mount  
the bracket. Extreme force is applied to the unit  
and the unit could fall off, possibly resulting in  
personal injuries.  
When Installing the Unit  
• Use nuts and bolts that are appropriate for the  
ceiling's or wall's structure and composition. Failure  
to do so may cause the speaker to fall, resulting in  
material damage and possible personal injury.  
• Avoid touching the unit's sharp metal edge to  
prevent injury.  
• To avoid electric shocks, be sure to switch off the  
unit's power when connecting speakers.  
• Tighten each nut and bolt securely. Ensure that the  
bracket has no loose joints after installation to  
prevent accidents that could result in personal  
injury.  
When the Unit is in Use  
• Do not place heavy objects on the unit as this may  
cause it to fall or break which may result in  
personal injury and/or property damage. In  
addition, the object itself may fall off and cause  
injury and/or damage.  
• Do not mount the unit in locations exposed to  
constant vibration. The mounting bracket can be  
damaged by excessive vibration, potentially  
causing the unit to fall, which could result in  
personal injury.  
• Do not operate the unit for an extended period of  
time with the sound distorting. This is an indication  
of a malfunction, which in turn can cause heat to  
generate and result in a fire.  
• (F-2000B, F-2000BT, F-2000W, F-2000WT only)  
Since the unit is designed for in-door use, do not  
install it outdoors. If installed outdoors, the aging of  
parts causes the unit to fall off, resulting in personal  
injury. Also, when it gets wet with rain, there is a  
danger of electric shock.  
• Do not stand or sit on, nor hang down from the unit  
as this may cause it to fall down or drop, resulting  
in personal injury and/or property damage.  
• (F-2000BTWP, F-2000WTWP only)  
• Have the unit checked periodically by the shop  
from where it was purchased. Failure to do so may  
result in corrosion or damage to the unit or its  
mounting bracket that could cause the unit to fall,  
possibly causing personal injury.  
When installing the unit in the snowy area, take  
appropriate measures to prevent snow from lying  
on the unit. If the snow lies on the unit, the unit may  
fall, causing personal injuries.  
3
 
2. GENERAL DESCRIPTION  
TOA's F-2000 Series Speakers are compact two-way speaker systems designed for high efficiency, wide  
range, and high power input handling capability. These speaker systems can be installed in a manner ideal for  
the location and intended application.  
3. FEATURES  
• 100º horizontal x 100º vertical wide directivity high-frequency horn.  
• Coverage angle can be changed to 80º horizontal x 80º vertical by attaching the supplied horn adapter.  
• Supplied bracket permits mounting to a wall, ceiling, or an optional speaker stand.  
• Combined use of the supplied bracket and optional mounting bracket allows the speakers to be mounted in  
many different applications, including pole mounting,*1 clusters and horizontal ceiling mounting*2.  
• Both the F-2000BTWP and F-2000WTWP feature a waterproof design (IPX4 standard) for protection from  
any adverse effects of outdoor installations.  
*1 Applies to the F-2000BTWP and F-2000WTWP.  
*2 Applies to the F-2000B, F-2000BT, F-2000W, and F-2000WT.  
4. DIMENSIONAL DIAGRAM  
Unit: mm  
[Top]  
[Bottom]  
Mounting holes  
Note  
Hole seals are adhered over the holes at the factory.  
Before attaching the speaker mounting bracket to this  
side, remove them using a pointed tool.  
6-M5 mounting screw hole  
(Effective screw depth: 14 mm)  
[Front]  
[Side]  
[Rear]  
235  
15º  
50  
244  
2-M5 mounting screw hole  
(Effective screw depth: 14 mm)  
4
 
5. IMPEDANCE CHANGE (F-2000BT, F-2000BTWP, F-2000WT, and F-2000WTWP only)  
To change the impedance, use a standard screwdriver to rotate the rotary switch on the speaker's rear to  
select the desired input power.  
Note: The switch is factory-preset to 170 Ÿ.  
Important  
Never set this switch to the "83 Ÿ" position when operating the speaker on 100 V line.  
Failure to follow this instruction could result in damage to the speaker or amplifier.  
6. ABOUT THE INPUT OVERLOAD PROTECTION CIRCUITRY  
(F-2000B and F-2000W only)  
The speaker system features internal input overload protection circuitry for both high and low frequencies.  
If an excessive input level is fed to the unit, the protection circuitry automatically cuts off the signal to the  
speaker driver.  
A drastic reduction in sound volume for the high or low frequency range indicates that the protection circuitry  
has been enabled.  
In such cases, simply reduce the amplifier volume. The protection circuitry will automatically reset in  
approximately 10 seconds. After reset, maintain the volume at a level slightly lower than before.  
Note  
This protection circuitry does not completely protect the unit against input overload. Depending on the type or  
duration of excessive power input, the protection circuitry might not be enabled, resulting in damage to the  
speaker driver. Also, if the excessive power input continues for a long period of time, the circuitry may not be  
capable of resetting to its original condition.  
Take care so that the speakers are not exposed to excessive power input.  
5
 
7. NOTES ON OUTDOOR INSTALLATION (F-2000BTWP and F-2000WTWP only)  
• Be sure to mount the speaker in a vertical (portrait-style) orientation.  
• Adjust the speaker's tilt angle within the shaded range shown below:  
[Wall and pole: 0º horizontal to 45º downward]  
[Under eaves: 15º downward to 45º downward]  
Note  
Mount the speaker so that its rear-mounted terminal  
cover is positioned on the upper side.  
Note  
The speaker faces 15°  
downward when mounting  
to a horizontal surface.  
15°  
0°  
(horizontal)  
0º  
(horizontal)  
(30°)  
45°  
45°  
• Install the speaker in locations exposed to an ambient temperature range of –10ºC to +50ºC. Exceeding this  
range could cause speaker failure.  
• Use the supplied terminal cover when connecting the speaker cable.  
[Terminal Cover Use]  
Input terminal  
2
Terminal cover (accessory)  
3
Tapping screw 4 x 12 (accessory)  
4
Bushing*  
1
[Stripped conductor]  
Speaker cable  
10 mm  
30 mm  
Speaker unit  
* Screwed onto the Terminal cover at the factory.  
Notes  
• For the speaker cable, use a cable with a diameter of 6 – 10 mm, which will fit the cable bushing.  
• To ensure waterproof capabilities, firmly mount the terminal cover to the speaker and tighten the bushing on  
the cover.  
Step 1. Feed the speaker cable through the bushing and terminal cover, then connect the cable to the input  
terminal.  
Step 2. Attach the terminal cover to the speaker.  
Attach the cover while pulling the cable so that it is not entangled inside the terminal cover.  
Step 3. Hold the terminal cover tightly to the speaker using the supplied screws.  
Step 4. Tighten the bushing.  
Note  
After tightening the bushing by hand, use a tool to further tighten it another 90º (1/4-turn) or so. Note  
that parts can be damaged by over-tightening.  
6
 
8. INSTALLATION  
8.1. Using the Supplied Brackets  
The speaker system is supplied with the following brackets. Use these brackets properly depending on the  
installation location and intended application.  
[Speaker bracket]  
[Joint bracket]  
[Wall bracket]  
30º  
8.1.1. When using only the supplied brackets  
Installation  
Application  
Location  
Speaker bracket Joint bracket Wall bracket Page  
P. 8  
When horizontal and vertical  
angle adjustability is desired.  
Wall  
When close wall surface  
mounting is desired*.  
P. 9  
P. 10  
P. 12  
Ceiling  
Vertical speaker mounting*  
Speaker Stand Mounting to the optional  
(Option) ST-16A Speaker Stand  
* Speaker coverage angles can only be adjusted in the vertical direction.  
8.1.2. When using both the supplied and optional mounting brackets  
Installation  
Location  
Application  
Option  
Speaker bracket Joint bracket  
Wall bracket Page  
P. 11  
Horizontal speaker HY-CM20B or  
mounting  
HY-CM20W  
HY-CL20B  
Ceiling  
Suspended speaker  
cluster mounting*  
P. 11  
P. 13  
SP-131 and  
YS-60B  
Pole  
Mounting to a pole  
* Speaker coverage angles can only be adjusted in the vertical direction.  
8.2. Speaker Cable Connections  
[Input terminal polarity]  
[Stripped conductor of cable]  
Sperker unit (rear)  
10 mm  
Input terminal  
(–)  
(+)  
BLACK RED  
7
 
8.3. Wall Mounting  
When adjusting horizontal and vertical angles:  
Use the supplied wall bracket, joint bracket, and speaker bracket to permit adjustment of the horizontal and  
vertical* speaker coverage angles.  
* Vertical installation.  
Horizontal: Max. 70º, Vertical: Max. 45º downward  
Horizontal installation. Horizontal: Max. 45º, Vertical: Max. 45º downward  
[Wall bracket mounting dimensions]  
[Installation example]  
4-ø6 mm  
Vertical speaker  
mounting  
2
Hexagon bolt M6 x 12  
(with plain washer  
45 mm  
and spring washer)  
Wall bracket  
Joint bracket  
1
Horizontal speaker  
mounting (indoor  
installation only)  
4
6
Fixing bolt M6 x 85  
[Vertical speaker installation]  
[Horizontal speaker installation]  
3
Speaker bracket  
Speaker bracket  
Speaker unit  
Machine screw  
Machine screw  
M5 x 20 (with plain  
washer and spring  
washer)  
M5 x 20 (with plain  
washer and spring  
washer)  
Speaker unit (rear)  
Speaker unit (rear)  
Step 1. Mount the wall bracket to the wall surface.  
Match the orientation of the arrow label with the horizontal direction (left or right) the speaker faces.  
Note: Hardware used for mounting the wall bracket to the wall is not supplied.  
• Arrow label orientation (Viewed from top of brackets)  
[Right-facing orientation]  
[Left-facing orientation]  
Wall bracket  
Wall bracket  
Arrow label  
Arrow label  
Joint bracket  
Joint bracket  
8
 
Step 2. Attach the joint bracket to the wall bracket using the supplied screws, adjust the horizontal speaker  
angle, then tighten the screws.  
Note: Match the orientation of the arrows on both the wall bracket and joint bracket.  
Step 3. Attach the speaker bracket to the speaker's rear using the supplied screws.  
Note: Attach the speaker bracket according to the speaker mounting orientation.  
Step 4. Mount the speaker to the joint bracket by inserting the speaker bracket into the joint bracket and  
loosely securing the fixing bolt for temporary speaker installation.  
Step 5. Connect the speaker cable to the input terminal.  
Note  
Use a terminal cover when installing the speaker outdoors. (Refer to p.6 for terminal cover  
attachment.)  
Step 6. Adjust the speaker's vertical mounting angle and tighten the fixing bolt.  
The speaker angle is adjustable in 7.5º steps.  
Note  
The mating surfaces of the speaker bracket and joint bracket are designed to interlock. Ensure that  
both parts are securely engaged with each other after mounting is complete.  
[Changing the orientation of the front panel logo]  
The front panel logo is affixed to the mesh net using double-faced tape. Peel off the logo carefully and reaffix it  
in the proper orientation.  
Mounting the speaker close to a wall surface  
Use both the supplied joint bracket and speaker bracket, and mount the joint bracket directly to a wall. After  
mounting the joint bracket, follow the Steps 3 – 6 above. In this configuration, the speaker can only be  
adjusted in the vertical direction*.  
* Vertical installation: Max. 37.5º downward, Horizontal installation: Max. 45º downward  
Note: Hardware used for mounting the joint bracket to the wall is not supplied.  
[Installation example]  
[Joint bracket mounting dimensions]  
4-ø6 mm  
Joint bracket  
Vertical speaker  
mounting  
45 mm  
6
4
Horizontal speaker  
mounting (indoor  
installation only)  
Fixing bolt  
M6 x 85  
Speaker bracket  
Speaker unit  
9
 
8.4. Ceiling Mounting  
Vertical orientation  
Use the supplied joint bracket and speaker bracket.  
Note  
Speaker coverage angles can only be adjusted in the vertical direction (Max. 45º downward).  
Adjust the speaker's tilt angle within the shaded range shown below:  
[Speaker angle vs. Bracket position]  
[Installation example]  
a
(horizontal)  
45º downward  
b
Joint bracket  
a
0°  
(horizontal)  
Speaker  
bracket  
45º  
b
30º  
15º  
Notes  
1
• Use an appropriate anchor bolt for supporting  
the full weight of the speaker and for the size  
of mounting hole in the joint bracket.  
Anchor bolt mounting hole  
Joint bracket  
• Ensure that the effective length of the anchor  
bolt is 25 mm or less.  
• When speaker rotation capability is not desired,  
secure with the 4 fixed mounting screw holes.  
Fixed mounting screw hole  
(4 holes)  
Fixing bolt M6 x 85  
2
Anchor bolt  
Ceiling board  
5
Machine screw  
3
M5 x 20 (with  
plain washer and  
spring washer)  
Speaker bracket  
Effective length  
A s h o l e s e a l s a r e  
Joint bracket  
adhered over the holes,  
remove them using a  
pointed tool before  
attaching the bracket.  
* Changing the orientation of the front panel logo  
The front panel logo is affixed to the mesh net using  
double-faced tape. Peel off the logo carefully and  
reaffix it in the proper orientation.  
Speaker unit  
Front panel logo*  
Step 1. Mount the joint bracket to the ceiling surface.  
[Joint bracket mounting dimensions]  
Note  
Hardware used for mounting the joint bracket to the ceiling is  
not supplied.  
4-ø6 mm  
ø10 mm  
Step 2. Attach the speaker bracket to the speaker's bottom using the  
supplied screws.  
45 mm  
10  
 
Step 3. Mount the speaker to the joint bracket by inserting the speaker bracket into the joint bracket and  
loosely securing the fixing bolt for temporary speaker installation.  
Step 4. Connect the speaker cable to the input terminal.  
Note  
Use a terminal cover when installing the speaker outdoors. (Refer to p. 6 for terminal cover  
attachment.)  
Step 5. Adjust the speaker's vertical mounting angle and tighten the fixing bolt.  
The speaker angle is adjustable in 7.5º steps.  
Note  
The mating surfaces of the speaker bracket and joint bracket are designed to interlock. Ensure that  
both parts are securely engaged with each other after mounting is complete.  
Horizontal orientation (F-2000B, F-2000BT, F-2000W, and F-2000WT only)  
[Installation example]  
Use the supplied joint bracket and speaker bracket in combination with  
the optional HY-CM20B or HY-CM20W Ceiling Mount Bracket.  
Refer to the instruction manual enclosed with the optional mounting  
bracket for its mounting details.  
Cluster configuration assembly  
(F-2000B, F-2000BT, F-2000W, and F-2000WT only)  
[Installation example]  
Use the supplied joint brackets and speaker brackets in  
combination with the optional HY-CL20B Cluster Bracket  
to permit a total of 4 speakers to be suspended from the  
ceiling as shown in the figure at right.  
Refer to the instruction manual enclosed with the  
optional mounting bracket for its mounting details.  
11  
 
8.5. Speaker Stand Mounting  
The speaker can be mounted on the optional ST-16A Speaker Stand using the supplied joint bracket and  
speaker bracket.  
[Installation example]  
Speaker unit  
A s h o l e s e a l s a r e  
adhered over the holes,  
remove them using a  
pointed tool before  
attaching the bracket.  
Machine screw  
M5 x 20 (with  
plain washer and  
spring washer)  
2
Max.180 cm  
Speaker bracket  
Butterfly nut  
(supplied with  
the ST-16A)  
3
3
Washer  
(supplied with  
the ST-16A)  
Fixing bolt M6 x 85  
1
Joint bracket  
Note  
Bracket  
(supplied with the ST-16A)  
Mount the speaker so that it faces  
within the range of 15º upward and  
downward.  
Hexagon bolt  
(supplied with the ST-16A)  
a
15°  
15°  
ST-16A (option)  
b
Step 1. Attach the joint bracket to the speaker stand bracket using  
the speaker stand's supplied bolt and nut.  
Step 2. Attach the speaker bracket to the speaker's bottom using the  
supplied screws.  
[Speaker angle vs. Bracket position]  
a
b
Step 3. Mount the speaker to the joint bracket by inserting the  
speaker bracket into the joint bracket and loosely securing  
the fixing bolt for temporary speaker installation.  
After adjusting the speaker's vertical mounting angle, tighten  
the fixing bolt.  
15º upward  
15º downward  
0°  
30°  
The speaker angle is adjustable in 7.5º steps.  
The mating surfaces of the speaker bracket and joint bracket  
are designed to interlock. Ensure that both parts are  
securely engaged with each other after mounting is  
complete.  
Speaker bracket  
Joint bracket  
Step 4. Connect the speaker cable to the input terminals.  
Note  
Use a terminal cover when installing the speaker outdoors.  
(Refer to p. 6 for terminal cover attachment.)  
Note  
For more information on mounting the bracket to the stand and stand usage, refer to the instruction manual  
enclosed with the ST-16A Speaker Stand.  
12  
 
8.6. Pole Mounting (F-2000BTWP and F-2000WTWP only)  
To mount the speaker on a pole with diameter of 9 – 34 cm, use the  
supplied wall bracket, joint bracket, and speaker bracket in combination  
with the optional SP-131 Pole Mount Bracket and YS-60B Pole Band.  
Speaker coverage angles can be adjusted in the horizontal and vertical  
direction*.  
[Installation example]  
* Horizontal: Max. 90º, Vertical: Max. 45º downward  
Note  
Although the SP-131 comes in 2 sets of brackets, use one set only.  
Plain washer for M8  
(supplied with the SP-131)  
Hexagon bolt M6 x 12  
(with plain washer  
and spring washer)  
Plain washer for M8  
(supplied with the SP-131)  
3
Hexagon bolt M8 x 20  
Spring washer for M8  
(supplied with the SP-131)  
(supplied with the SP-131)  
Wall bracket  
Nut for M8  
(supplied with the SP-131)  
YS-60B (option)  
SP-131 (option)  
Joint bracket  
2
1
3
7
5
Fixing bolt M6 x 85  
[Speaker bracket mounting position]  
4
Speaker bracket  
Note  
Set the speaker in a vertical orientation,  
then attach the bracket so that the rear-  
mounted terminal cover is positioned  
above the mount.  
Speaker unit  
Machine screw  
M5 x 20 (with plain  
washer and spring  
washer)  
Speaker (rear)  
13  
 
Step 1. Attach the wall bracket to the SP-131 Pole Mount Bracket.  
Match the orientation of the arrow label with the horizontal direction (left or right) the speaker faces.  
Use the bolts supplied with the SP-131.  
• Arrow label orientation (Viewed from top of brackets)  
[Right-facing orientation]  
[Left-facing orientation]  
Pole  
Pole  
SP-131  
SP-131  
Wall bracket  
Wall bracket  
Joint bracket  
Arrow label  
Arrow label  
Joint bracket  
Step 2. Attach the SP-131 to a pole using the YS-60B.  
Step 3. Attach the joint bracket to the wall bracket using the supplied screws, adjust the horizontal speaker  
angle, then tighten the screws.  
Note  
Match the orientation of the arrows on both the wall bracket and joint bracket.  
Step 4. Attach the speaker bracket to the speaker's rear using the supplied screws.  
Note  
Set the speaker in a vertical orientation, then attach the bracket so that the rear-mounted terminal  
cover is positioned above the mount.  
Step 5. Mount the speaker to the joint bracket by inserting the speaker bracket into the joint bracket and  
loosely securing the fixing bolt for temporary speaker installation.  
Step 6. Connect the speaker cable to the input terminal.  
Note  
Use a terminal cover when installing the speaker outdoors. (Refer to p. 6 for terminal cover  
attachment.)  
Step 7. Adjust the speaker's vertical mounting angle and tighten the fixing bolt.  
The speaker angle is adjustable in 7.5º steps.  
Note  
The mating surfaces of the speaker bracket and joint bracket are designed to interlock. Ensure that  
both parts are securely engaged with each other after mounting is complete.  
14  
 
9. REDUCING THE SPEAKER COVERAGE ANGLE  
The speaker's coverage angle can be reduced to 80º horizontal x 80º vertical from its normal range of 110º x  
110º by attaching the supplied horn adapter to the speaker's horn section.  
[Without horn adapter]  
[With horn adapter]  
110º horizontal  
80º horizontal  
80° vertical  
100° vertical  
[Attaching the horn adapter]  
Horn adapter  
Note  
2
Take care not to touch the  
speaker diaphragm during  
attachment.  
Tapping screw 4 x 12  
Mesh speaker grill  
Countersunk head  
tapping screw 4 x 12  
1, 3  
Logo  
Note  
Because the logo is affixed using double-faced tape, peel it off carefully.  
Step 1. Peel off the logo carefully, then remove the screw underneath to detach the mesh speaker grill.  
Step 2. Attach the supplied horn adapter using the supplied screws.  
Step 3. Replace the mesh grill and logo.  
15  
 
10. REPAINTING THE SPEAKER  
Follow the procedure below when repainting the speaker grill and cabinet.  
Note  
Take care not to touch the speaker diaphragm during work.  
Step 1. Peel off the logo carefully, then remove the screw underneath to detach the mesh speaker grill.  
[Detaching the mesh grill]  
Mesh speaker grill  
Countersunk head  
tapping screw 4 x 12  
Baffle (Masking area)  
Logo  
Note  
Because the logo is affixed using double-faced tape, peel it off carefully.  
Step 2. Wipe clean the mesh grill and speaker cabinet with a soft cloth dampened in a detergent.  
Note  
Do not use thinner or other volatile liquids to clean the grill and cabinet.  
Step 3. Use spray paint to apply thin coat evenly overall the speaker.  
Notes  
• Avoid painting with a roller or brush, as the grill holes could become clogged with paint.  
• Securely mask the entire baffle surface before painting.  
• Use appropriate paints for the speaker grill and cabinet materials.  
Grill: Rolled steel plate (acrylic paint)  
Cabinet: Fire-resistant HIPS resin  
Step 4. After the paint has dried, apply another light coat.  
Note  
Repeating Step 3, apply 2 or more light coats of paint.  
Application of one thick coat of paint all at once may cause drips or unevenness to show up in the  
painted finish, or clog the mesh holes.  
Step 5. After the paint has dried, replace the mesh grill and logo.  
16  
 
11. SPECIFICATIONS  
11.1. F-2000B and F-2000W  
Model No.  
F-2000B  
F-2000W  
Enclosure Type  
Power Handling Capacity  
Bass-reflex type  
60 W (continuous pink noise)  
180 W (continuous program)  
8 Ÿ  
Rated Impedance  
Output Sound Pressure  
Level  
92 dB (1 W, 1 m) at installation in a semianechoic field  
93 dB (1 W, 1 m) at installation in a semianechoic field (with horn adapter)  
65 – 20,000 Hz, –10 dB at installation in a semianechoic field  
2.5 kHz  
Frequency Response  
Crossover Frequency  
Directivity Angle  
Horizontal: 110º, Vertical: 100º  
Horizontal: 80º, Vertical: 80º (with horn adapter)  
Woofer: 20 cm cone-type  
Speakers  
Tweeter: 25 mm dome-type  
Input Terminals  
Enclosure  
Push-in terminals  
HIPS, black  
HIPS, white  
Mesh Speaker Grill  
Speaker Bracket  
Joint Bracket, Wall Bracket  
Dimensions  
Surface-treated steel plate, black, paint  
Aluminum die-cast, black, paint  
Steel plate, t2.0, black, paint  
Surface-treated steel plate, white, paint  
Aluminum die-cast, white, paint  
Steel plate, t2.0, white, paint  
244 (w) x 373 (h) x 235 (d) mm  
Weight  
6.5 kg (including the supplied brackets)  
Speaker bracket ... 1, Joint bracket ... 1, Wall bracket ... 1, Fixing bolt M6 x 85 ... 1,  
Hexagon bolt M6 x 12 (with plain washer and spring washer) ... 2,  
Machine screw M5 x 20 (with plain washer and spring washer) ... 4,  
Tapping screw 4 x 12 ... 4, Horn adapter ... 1  
Accessories  
Optional Products  
Ceiling mount bracket: HY-CM20B  
Ceiling mount bracket: HY-CM20W  
Cluster bracket:  
Speaker stand:  
HY-CL20B  
ST-16A  
Cluster bracket:  
Speaker stand:  
HY-CL20B  
ST-16A  
Note: The design and specifications are subject to change without notice for improvement.  
17  
 
11.2. F-2000BT and F-2000WT  
Model No.  
F-2000BT  
F-2000WT  
Enclosure Type  
Bass-reflex type  
60 W  
Power Handling Capacity  
Rated Impedance  
170 Ÿ (60 W), 330 Ÿ (30 W), 670 Ÿ (15 W), 3.3 kŸ (3 W)  
Output Sound Pressure  
Level  
92 dB (1 W, 1 m) at installation in a semianechoic field  
93 dB (1 W, 1 m) at installation in a semianechoic field (with horn adapter)  
65 – 20,000 Hz, –10 dB at installation in a semianechoic field  
2.5 kHz  
Frequency Response  
Crossover Frequency  
Directivity Angle  
Horizontal: 110º, Vertical: 100º  
Horizontal: 80º, Vertical: 80º (with horn adapter)  
Woofer: 20 cm cone-type  
Speakers  
Tweeter: 25 mm dome-type  
Input Terminals  
Enclosure  
Push-in terminals  
HIPS, black  
HIPS, white  
Mesh Speaker Grill  
Speaker Bracket  
Joint Bracket, Wall Bracket  
Dimensions  
Surface-treated steel plate, black, paint  
Aluminum die-cast, black, paint  
Steel plate, t2.0, black, paint  
Surface-treated steel plate, white, paint  
Aluminum die-cast, white, paint  
Steel plate, t2.0, white, paint  
244 (w) x 373 (h) x 235 (d) mm  
Weight  
7.4 kg (including the supplied brackets)  
Speaker bracket ... 1, Joint bracket ... 1, Wall bracket ... 1, Fixing bolt M6 x 85 ... 1,  
Hexagon bolt M6 x 12 (with plain washer and spring washer) ... 2,  
Machine screw M5 x 20 (with plain washer and spring washer) ... 4,  
Tapping screw 4 x 12 ... 4, Horn adapter ... 1  
Accessories  
Optional Products  
Ceiling mount bracket: HY-CM20B  
Ceiling mount bracket: HY-CM20W  
Cluster bracket:  
Speaker stand:  
HY-CL20B  
ST-16A  
Cluster bracket:  
Speaker stand:  
HY-CL20B  
ST-16A  
Note: The design and specifications are subject to change without notice for improvement.  
18  
 
11.3. F-2000BTWP and F-2000WTWP  
Model No.  
F-2000BTWP  
F-2000WTWP  
Enclosure Type  
Bass-reflex type  
60 W  
Power Handling Capacity  
Rated Impedance  
Output Sound Pressure  
Level  
170 Ÿ (60 W), 330 Ÿ (30 W), 670 Ÿ (15 W), 3.3 kŸ (3 W)  
92 dB (1 W, 1 m) at installation in a semianechoic field  
93 dB (1 W, 1 m) at installation in a semianechoic field (with horn adapter)  
65 – 20,000 Hz, –10 dB at installation in a semianechoic field  
2.5 kHz  
Frequency Response  
Crossover Frequency  
Directivity Angle  
Horizontal: 110º, Vertical: 100º  
Horizontal: 80º, Vertical: 80º (with horn adapter)  
Woofer: 20 cm cone-type  
Speakers  
Tweeter: 25 mm dome-type  
Input Terminals  
Push-in terminals  
Water Resistance  
Operating Temperature  
Enclosure  
IPX4  
–10 ºC to +50 ºC  
HIPS, black  
HIPS, white  
Mesh Speaker Grill  
Surface-treated steel plate, black,  
anti-rust paint  
Surface-treated steel plate, white,  
anti-rust paint  
Speaker Bracket  
Joint Bracket, Wall Bracket  
Dimensions  
Aluminum die-cast, black, paint  
Aluminum die-cast, white, paint  
Stainless steel (SUS 304), t2.0  
244 (w) x 373 (h) x 235 (d) mm  
7.4 kg (including the supplied brackets)  
Weight  
Accessories  
Speaker bracket ... 1, Joint bracket ... 1, Wall bracket ... 1, Fixing bolt M6 x 85 ... 1,  
Hexagon bolt M6 x 12 (with plain washer and spring washer) ... 2,  
Machine screw M5 x 20 (with plain washer and spring washer) ... 4,  
Tapping screw 4 x 12 ... 8, Horn adapter ... 1, Terminal cover ... 1  
Pole mount bracket: SP-131  
Optional Products  
Pole band:  
YS-60B  
Note: The design and specifications are subject to change without notice for improvement.  
19  
 
 

Tektronix Stereo Amplifier 5A20N User Manual
Tokina Camcorder Accessories MVH 2D User Manual
Toshiba DVD Player SD 4205 User Manual
Toshiba Flat Panel Television 65H14 User Manual
TRENDnet Network Hardware TU2ET100 User Manual
Trion Air Cleaner HE Series User Manual
True Fitness Home Gym Z5 Elliptical User Manual
Viking Cooktop F20112E User Manual
Volvo Automobile C70 User Manual
Vulcan Hart Indoor Furnishings Wallmnt Chrbkr User Manual